Aluminum edge pulls and tab pulls give cabinet doors and drawers a clean finger grip without knobs. Most profiles come in 48" to 144" lengths to cut to the width of each front; tabs also come pre-cut. Choose your panel thickness, then pick a pull.
1. Your door or drawer front thickness
Most pulls fit 3/4" panels. The Drawer Pull Tab fits anything from 1/2" to 7/8".
Flush & Edge Pulls
Low-profile pulls sold in lengths to cut to the width of each door or drawer front.
Continuous Mount Pull
Full-length pull that runs the width of a door or drawer front in one continuous line.
| Fits | 3/4" panel |
|---|---|
| Finish | Clear anodized, black or white powder coat |
| 48", 72" or 96" lengths | View OptionsOptions |
Flush Mortise Pull
Low-profile pull for sliding doors, drawers, and tight clearances.
| Fits | 13/16" panel |
|---|---|
| Finish | Clear anodized |
| 48" to 144" lengths | View OptionsOptions |
Kerf Mount Pull
Minimalist pull for a flush, built-in look on cabinets and drawers.
| Fits | 3/4" panel |
|---|---|
| Finish | Clear anodized |
| 48" to 144" lengths | View OptionsOptions |
Drawer Pull
Slim drawer pull with a comfortable grip and clean lines.
| Fits | 3/4" or 13/16" panel |
|---|---|
| Finish | Clear anodized |
| 48" to 144" lengths | View OptionsOptions |
Angled Drawer Pull
Angled grip that improves hand clearance on drawers and panels.
| Fits | 3/4" or 13/16" panel |
|---|---|
| Finish | Clear anodized |
| 48" to 144" lengths | View OptionsOptions |
Top Mount Pull
Low-profile architectural pull for casework, panels, and custom millwork.
| Fits | 5/8" or 3/4" panel |
|---|---|
| Finish | Clear anodized |
| 48" to 144" lengths | View OptionsOptions |
Tab Pulls
Tab profiles give a door or drawer a defined grip point. Run them full length, cut your own short tabs, or buy pre-cut tabs.
Bulb Flat Tab
Rounded bulb-edge tab with a smooth grip and modern styling.
| Fits | 3/4" panel |
|---|---|
| Finish | Clear anodized |
| 48" to 144" lengths | View OptionsOptions |
San Andreas Tab
Angular architectural tab that adds depth to modern cabinetry.
| Fits | 3/4" panel |
|---|---|
| Finish | Clear anodized |
| 48" to 144" lengths | View OptionsOptions |
Flush Mount Tab
Tab pull with a low-profile, built-in look.
| Fits | 3/4" panel |
|---|---|
| Finish | Clear anodized or black powder coat |
| 48", 72" or 96" lengths | View OptionsOptions |
Angled Bulb Flat Tab
Angled bulb tab that improves grip and cabinet access.
| Fits | 3/4" panel |
|---|---|
| Finish | Clear anodized |
| 48" to 144" lengths | View OptionsOptions |
1.5" Angled Bulb Flat Tab
The Angled Bulb Flat Tab pre-cut to 1.5" tabs, 10 per pack.
| Fits | 3/4" panel |
|---|---|
| Finish | Clear or black anodized |
| 1.5" tabs, 10-pack | View OptionsOptions |
Drawer Pull Tab
Short tab with a lip grip for doors and drawer fronts.
| Fits | 1/2" to 7/8" panels |
|---|---|
| Finish | Clear anodized, brushed nickel, chrome, black powder coat |
| 3", 4" or 6" tabs | View OptionsOptions |
Aluminum Edge Pulls and Tab Pulls for Cabinets and Millwork
Orange Aluminum’s pulls are extruded 6063-T5 aluminum profiles for cabinet doors, drawers, closet systems, and custom millwork.
Sizing for your panels
| Panel thickness | Pulls that fit |
|---|---|
| 5/8" | Top Mount Pull, Drawer Pull Tab |
| 3/4" | All except Flush Mortise Pull |
| 13/16" | Flush Mortise Pull, Drawer Pull, Angled Drawer Pull, Drawer Pull Tab |
Finishes and lengths
Clear anodized on every profile, with powder coat, black anodized, brushed nickel, and chrome on select pulls. Lengths and finishes for each pull are listed under View Options.
Used in kitchen and bath cabinetry, closet systems, office furniture, retail fixtures, hospitality interiors, and custom millwork.
Edge Pull & Tab Pull FAQ
Choosing a pull
What are edge pulls?
Edge pulls sit along the top or side edge of a cabinet door or drawer front, so the grip follows the edge instead of sitting on the face.
What is a finger pull?
A finger pull is shaped so your fingers hook behind a lip or into a recess instead of wrapping around a handle. The edge pulls and tab pulls on this page are all finger pulls.
What is a tab pull?
A tab pull is a short pull with a lip that projects past the edge of a door or drawer front. Cut tabs from a full-length profile, or order pre-cut Drawer Pull Tabs (3", 4", or 6") or 1.5" Angled Bulb Flat Tabs.
What is the difference between an edge pull and a tab pull?
An edge pull keeps the grip in line with the panel edge. A tab pull projects a lip past the edge, which gives more to hold.
Sizing
What panel thickness do these pulls fit?
Most profiles fit 3/4" panels. Flush Mortise Pull fits 13/16". Drawer Pull and Angled Drawer Pull come in 3/4" and 13/16". Top Mount Pull comes in 5/8" and 3/4". Drawer Pull Tabs fit panels from 1/2" to 7/8".
What lengths are available?
Most profiles come in 48", 72", 96", and 144" lengths. Continuous Mount Pull and Flush Mount Tab come in 48", 72", and 96". Cut them to the width of each door or drawer front.
Cutting, finishes, and ordering
How do you cut aluminum pulls?
Use a miter saw with a carbide-tipped blade rated for non-ferrous metal, cut slowly, and deburr the cut edge. Wear eye protection.
What finishes are available?
Every profile comes in clear anodized. Continuous Mount Pull also comes in black or white powder coat, Flush Mount Tab in black powder coat, the 1.5" Angled Bulb Flat Tab in black anodized, and Drawer Pull Tabs in brushed nickel, chrome, and black powder coat.
Does anodized aluminum rust?
No. Rust is iron oxide, and aluminum contains no iron. Aluminum forms a thin protective oxide layer on its own, and anodizing makes that layer thicker and harder.
Is there volume pricing?
Yes. Quantity discounts apply automatically at checkout, and the tiers are shown when you open View Options.
Can I get a custom aluminum pull profile?
Yes. We offer custom aluminum profiles and extrusion services. Contact us to start a request.